So, after I've run the program, do I try and upload the file into create on IMVU?
It doesn't really tell me what to do, just how far to slide the bar.

grabmynuts wrote:

So, after I've run the program, do I try and upload the file into create on IMVU?
It doesn't really tell me what to do, just how far to slide the bar.

Yes .... but remember the offsetter only works with PRB 1.5 file....How to know that it has offset your file? when you load a file...on the left box...you will see a series of letter/number.....when you successfully offset your file....a new number/letter will appear on the right box...remember that you can only run the file ones in the offsetter or you will receive an error....then load your offset file on imvu create! then submit it as you normally do...Hope this helps....Good luck and enjoy

grabmynuts wrote:

So, after I've run the program, do I try and upload the file into create on IMVU?
It doesn't really tell me what to do, just how far to slide the bar.

Once the program is done, you will get a little pop up message that says "done". Then it is ready to upload into create mode on IMVU.

I could not install hash offsetter due to a problem with .NET framework 4.5.2 not installing...its a googleable issue...with that said, coupled with my enthusiastic mood to try these new poses out, can I still do the offsets manually (x 0.001111) as the tutorial shows? The poses I have are PRB 1.5's

I am new to this and have some basic questions which may or may not belong here in this post, so I'll at least stay to the point... for instance,a pose I have has a product name, "chair", but when I upload to imvu there is no chair, the pose is time locked and appears after several minutes, that's fine, but my question is ,if this is being peer reviewed as a chair...there's no chair...fail, after you stop laughing, please explain/help, Thanks in advance.

Luigi23 wrote:

I could not install hash offsetter due to a problem with .NET framework 4.5.2 not installing...its a googleable issue...with that said, coupled with my enthusiastic mood to try these new poses out, can I still do the offsets manually (x 0.001111) as the tutorial shows? The poses I have are PRB 1.5's

I am new to this and have some basic questions which may or may not belong here in this post, so I'll at least stay to the point... for instance,a pose I have has a product name, "chair", but when I upload to imvu there is no chair, the pose is time locked and appears after several minutes, that's fine, but my question is ,if this is being peer reviewed as a chair...there's no chair...fail, after you stop laughing, please explain/help, Thanks in advance.

Why don't yo just name it invisible chair or invisible furniture...good luck with the hash offsetter...try to fix your net frame work...this hash offsetter really help a lot...but you can use the manual as well....it just take time....enjoy the forums!

Luigi23 wrote:

I could not install hash offsetter due to a problem with .NET framework 4.5.2 not installing...its a googleable issue...with that said, coupled with my enthusiastic mood to try these new poses out, can I still do the offsets manually (x 0.001111) as the tutorial shows? The poses I have are PRB 1.5's

I am new to this and have some basic questions which may or may not belong here in this post, so I'll at least stay to the point... for instance,a pose I have has a product name, "chair", but when I upload to imvu there is no chair, the pose is time locked and appears after several minutes, that's fine, but my question is ,if this is being peer reviewed as a chair...there's no chair...fail, after you stop laughing, please explain/help, Thanks in advance.

The video manual is less effective and takes a long time to do. We highly suggest uninstalling / reinstalling the latest version of the .Net framework in order to run the hash offsetter.

For safety of little scientiest i say
it will be a quite lot of work to you but .you should make all mesh PRB 1.5 ..

Your suggestion would not help. Just upgrading the mesh to PRB version 1.5 would not make the chkn safe. All files within the chkn must be upgraded to PRB version 1.5; mesh, animation, morphs, skeletons, and texture maps.

i know it be time consuming but thats how it be beneficial for all community .
I have dream to see (all product as PRB ) no regular.

All of our products have been upgraded to PRB's version 1.5. We moved to the new 1.5 system back in November of last year.

we all ppls that know how to make prb can help that divides work.

We already have a PRB school which teaches people how to make AP PRB's. UFI PRB's are not something we can easily teach, but we do cover AP PRB's.

We already have a PRB school which teaches people how to make AP PRB's. UFI PRB's are not something we can easily teach, but we do cover AP PRB's.

yes and i have learned alot since i joined :D

Sorry for kind of the late post here, but I am having an issue with the Mesh Offsetter... I would like to talk to someone about this through PM or Skype if possible. If not, I can just post it here. Thank you

TheSKP wrote:

Sorry for kind of the late post here, but I am having an issue with the Mesh Offsetter... I would like to talk to someone about this through PM or Skype if possible. If not, I can just post it here. Thank you

If the offsetter doesn't work for you update your .Net framework install.
If the program freezes just wait a while for it to finish.
If the products still fails after using the offsetter try a different strength.


If none of those solve your issue send a private message to Don Von. He can help you with it.